Countertop Reinforcement

Tools for Concrete work

Site Wagman Metal Products York, PADarbying or bull floating should be done immediately after "screeding", or after the concrete has been tamped if tamping was done.This process should be finished before excess moisture or bleedwater appear on the surface.

The purpose of darbying or bull floating concrete is to level ridges and fill voids left by the screeding operation. It should also slightly embed the coarse aggregate to make subsequent finishing operations easier.

Be careful when using these tools not to close up or seal the surface of the concrete, which may cause blistering or scaling.

Use a bull float for areas too large to reach with a darby, though it may produce a wavier surface.


Purpose: To level ridges, fill voids, and smooth the surface in preparation for troweling. Floats also can be used to work in dry-shake color hardener. Unlike trowel finishing, floating won't close the surface, which is important at this stage to permit water to bleed out. A float also helps bring paste to the surface by pushing down the coarse aggregate.

Wagman Metal Products Bull Float.Site Portland Cement Association , Portland Cement Association in Skokie, IL Wagman Metal Products

What's available: The most common floats for decorative concrete work are made of magnesium, aluminum, or wood. Less common float materials include stainless steel, rubber, and laminated wood or canvas resin. Bull floats are used to work large areas of concrete and are typically 8 inches in width and 3 to 10 feet in length. Hand floats range in width from 3 to 5 inches and in length from 12 to 24 inches. Most floats are available with rounded or square ends. Round-end floats work more easily in tight corners and help to minimize lap marks.

Site Wagman Metal Products York, PAWatch Bob Harris demonstrate the use of various hand floats and darbies:

Video: Hand Floats
Length: 03:49
Watch Bob Harris demonstrate the use of various hand floats and darbies.

Video: Bull Floats
Length: 02:46
Watch Bob Harris demonstrate the use of various bull floats, including wood and magnesium floats.

Buying tips:

  • Look for magnesium bull floats with top reinforcement ribbing, which adds strength and prevents distortion.
  • You'll need to purchase bull float handles separately. They are typically offered in aluminum, magnesium, or fiberglass in 4- to 10-foot lengths, and often can be interlocked to create longer lengths. Buy fiberglass handles if you plan to work in areas with overhead power lines, because fiberglass won't conduct electricity.
  • Not all bull floats come with bracket assemblies for attaching handles, so you may need to purchase those separately as well. For better control, buy an adjustable tilt-action bracket that lets you change the float pitch with a simple turn of the handle.
  • On hand floats, look for handles that are screwed to the blade so the handle can be replaced if it splits or breaks. The handle also should be positioned for good balance, allow adequate knuckle clearance, and have a comfortable grip.
  • Wood hand floats are available in variety of types, including teakwood, bodark wood, and redwood. Each type may produce a different surface texture, so it's always wise to experiment.
  • Rubber floats are good choices for producing textured or slip-resistant finishes because they bring more sand to the surface.

Average costs: You'll pay about $100 to $125 for a 4-foot magnesium bull float with bracket, and $18 for a 14-inch magnesium hand float. The price of wood floats varies, depending on the type of wood used, but will generally be lower than the cost of magnesium.

Hand Floats

Floating should be done after the edging and jointing operations. Floating helps remove imperfections and produces a flatter surface. It also compacts the slab and the mortar at the surface in preparation for later finishing operations.

Floating can be performed by machine or by hand. If floating is done by hand, a magnesium float is recommended, particularly on air entrained or lightweight concrete.

Share this article

Related Posts

Tools for Concrete
Tools for Concrete

Latest Posts
Cedar Rapids Crushers
Cedar Rapids…
Based on the classic ElJay design, the…
Used Meyers Snow Plow parts
Used Meyers Snow…
Users input a ZIP code and then use drop-down…
Crusher Rock
Crusher Rock
We now carry the New and Improved model…
Crane Truck Games
Crane Truck Games
Push the gas pedal and race in a city…
Rubber tyred Roller
Rubber tyred…
HAMM offers a wide range of products…
Featured posts
  • Tools for Concrete
  • Hand tools for Construction
  • Tools for smoothing Concrete
  • List of tools for Construction
  • Reach Forklifts
  • Reach Fork Trucks
  • Forklift Material Handling
  • Cat p5000 Forklift Specs
  • Used Forklifts trucks
Copyright © 2024 l All rights reserved.